After several iterations and alot of help from Flames1950, I have put together a diagram showing the PT, OT, switches, jacks, & fuse wiring. This is designed to work in tandem with Billy Batz's layout... This diagram will show all of the wiring that was omitted on BB's layout. Thanks again to Flames for saving me countless hours of frustration & troubleshooting!!!
EDIT: Fixed per George's comment below... Also added extra detail on the indicator lamp wiring! check to see if you have a 120vac or a 6vac lamp and follow the wiring instructions on the diagram.... Also, see below for alternate Board Layout...
I have received a few PM's on where Billy Batz's JTM45/100 Layout is located:
http://homepage.mac.com/gaden/.Public/6 ... Layout.pdf
Supplemental Wiring Diagrams
Moderator: VelvetGeorge
- gutpile
- Senior Member
- Posts: 1370
- Joined: Wed Nov 01, 2006 3:47 pm
- Just the numbers in order: 13492
- Location: Northville, MI
Supplemental Wiring Diagrams
- Attachments
-
- JTM45100 Wiring rev1.jpg
- (154.17 KiB) Downloaded 409 times
Last edited by gutpile on Wed May 21, 2008 8:55 pm, edited 6 times in total.
Metro Clips
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
- VelvetGeorge
- Site Owner
- Posts: 7233
- Joined: Tue Oct 14, 2003 5:12 pm
- Just the numbers in order: 13492
- Location: The Murder Mitten
- Contact:
- gutpile
- Senior Member
- Posts: 1370
- Joined: Wed Nov 01, 2006 3:47 pm
- Just the numbers in order: 13492
- Location: Northville, MI
Fixed!
George, thanks for the awesome amps! How do you make these????
George, thanks for the awesome amps! How do you make these????
Metro Clips
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
-
- Senior Member
- Posts: 8566
- Joined: Fri Dec 10, 2004 8:49 pm
- gutpile
- Senior Member
- Posts: 1370
- Joined: Wed Nov 01, 2006 3:47 pm
- Just the numbers in order: 13492
- Location: Northville, MI
I can add that BB, it is shown on your diagram already... I was going after trying to show the wiring that you did not show on yours... it makes sense to add it though so it is consistent... I'll update it tomorrow...
Thanks,
Mike
Thanks,
Mike
Metro Clips
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
- gutpile
- Senior Member
- Posts: 1370
- Joined: Wed Nov 01, 2006 3:47 pm
- Just the numbers in order: 13492
- Location: Northville, MI
Here's an alternative Board Layout... added routing of wire off of the 27k resistor to speaker jack and grounding of input jacks and pots... replaced 32uf board cap on BB's layout with 22uf, also replaced the 150k in the bias with a 180k...
- Attachments
-
- Board Layout.jpg
- (111.09 KiB) Downloaded 267 times
Metro Clips
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI
Amps:Metro-(JTM45,50w,'69 spec 100w,45/100,100wMV,Bluesbreaker Combo),Orig. 65BFTR
Axes:LP Custom,Am. Strat,Am. Tele,61 SGRI