I found the PPIMV redundant, so only needed one pot with DPDT switching
I use these switches from TAD in Germany. They are very tightly linked with MOJO so might be worth trying?
https://www.tubeampdoctor.com/en/shop_P ... rvolume_29
50w plexi vs 2204 (I’m confused)
Moderator: VelvetGeorge
- neikeel
- Senior Member
- Posts: 7231
- Joined: Tue Dec 06, 2005 8:31 am
- Location: Suffolk, England
-
- Senior Member
- Posts: 1099
- Joined: Tue Sep 10, 2013 9:09 pm
- Just the numbers in order: 13492
Re: 50w plexi vs 2204 (I’m confused)
This type of switched pot always works well for me but unfortunately this seller does not have any 1m values. Maybe try Mouser or Digikey...https://theartoftone.com/cts-500k-push- ... tolerance/
-
- Senior Member
- Posts: 51
- Joined: Tue Nov 13, 2018 6:35 am
- Just the numbers in order: 13492
Re: 50w plexi vs 2204 (I’m confused)
I'll check them both out, however with shipping Australia it starts to get pricey. Still thinking I might use 2 x of the CTS with SPDP (on the 1987 bright vol and master vol) that VS have, I plan to use CTS pots on the amp.
I realize its controversial topic regarding resistor and capacitor types, but I read an article saying the only place to gain any benefit from carbon comp resistor it at v2 plate, is this right? Also, the layout has silver mica caps except for the bright cap which looks to be ceramic - is this correct?
I realize its controversial topic regarding resistor and capacitor types, but I read an article saying the only place to gain any benefit from carbon comp resistor it at v2 plate, is this right? Also, the layout has silver mica caps except for the bright cap which looks to be ceramic - is this correct?
- neikeel
- Senior Member
- Posts: 7231
- Joined: Tue Dec 06, 2005 8:31 am
- Location: Suffolk, England
Re: 50w plexi vs 2204 (I’m confused)
I can send you a pot (postage is not too bad).Explorerman wrote: ↑Wed Feb 06, 2019 3:39 pmI'll check them both out, however with shipping Australia it starts to get pricey. Still thinking I might use 2 x of the CTS with SPDP (on the 1987 bright vol and master vol) that VS have, I plan to use CTS pots on the amp.
I realize its controversial topic regarding resistor and capacitor types, but I read an article saying the only place to gain any benefit from carbon comp resistor it at v2 plate, is this right? Also, the layout has silver mica caps except for the bright cap which looks to be ceramic - is this correct?
I use Pihers and generally avoid cc resistors unless like for like in a resto.
I also use RS silver micas and mustards (I pick them up here an there when I find good prices on them as my original stashes have run out).
Yes you are correct regarding kit specs.
The reason I use an extra pot is that I can set my plexi and my 2204 pots and switch between the two quite quickly for different tones (I have been too busy with other stuff to footswitch this one but the Granger optofet jack works well.
Neil
-
- Senior Member
- Posts: 1099
- Joined: Tue Sep 10, 2013 9:09 pm
- Just the numbers in order: 13492
Re: 50w plexi vs 2204 (I’m confused)
I agree with Neikeel on the resistors. Carbon comps were rarely used in older Marshalls and will only add extra noise into the circuit. Marshall used carbon film Pihers in the early amps and then switch to Iskra carbon films. They are nice in a build but are pretty pricey these days if you do find a full set. I have always used the carbon films from Valvestorm but do like to use metal films for the 1m and 68k's on the input. The v1 grid leak and grid stopper resistors can add noise to the circuit so I like to use a quality metal film in those spots.
-
- New Member
- Posts: 46
- Joined: Mon Feb 20, 2017 12:25 pm
- Just the numbers in order: 13492
Re: 50w plexi vs 2204 (I’m confused)
Not to hijack this thread , But I have used and use CC resistors as well as CF resistors in all my builds and I don't notice any unwanted noise at all... All of my builds are quiet as a church mouse volume up or down... Just my 2cents..
-
- Senior Member
- Posts: 51
- Joined: Tue Nov 13, 2018 6:35 am
- Just the numbers in order: 13492
Re: 50w plexi vs 2204 (I’m confused)
Neikeel, I sent you a PM regarding the pot, but looks like its stuck in my outbox, I can't seem to work out why it won't send...neikeel wrote: ↑Wed Feb 06, 2019 4:51 pmI can send you a pot (postage is not too bad).Explorerman wrote: ↑Wed Feb 06, 2019 3:39 pmI'll check them both out, however with shipping Australia it starts to get pricey. Still thinking I might use 2 x of the CTS with SPDP (on the 1987 bright vol and master vol) that VS have, I plan to use CTS pots on the amp.
I realize its controversial topic regarding resistor and capacitor types, but I read an article saying the only place to gain any benefit from carbon comp resistor it at v2 plate, is this right? Also, the layout has silver mica caps except for the bright cap which looks to be ceramic - is this correct?
I use Pihers and generally avoid cc resistors unless like for like in a resto.
I also use RS silver micas and mustards (I pick them up here an there when I find good prices on them as my original stashes have run out).
Yes you are correct regarding kit specs.
The reason I use an extra pot is that I can set my plexi and my 2204 pots and switch between the two quite quickly for different tones (I have been too busy with other stuff to footswitch this one but the Granger optofet jack works well.